View M27C1001-15B1_1670047.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

april 2006 rev 5 1/24 1 m27c1001 1 mbit (128 kbit x 8) uv eprom and otp eprom features 5v 10% supply voltage in read operation access time: 35ns low power consumption: ? active current: 30 ma at 5 mhz ? standby current: 100 a programming voltage: 12.75v 0.25v programming time: 100 s/word electronic signature ? manufacturer code: 20h ? device code: 05h ecopack? packages available 1 32 32 1 fdip32w (f) pdip32 (b) plcc32 (c) tsop32 (n) 8 x 20 mm www.st.com
contents m27c1001 2/24 contents 1 summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 device description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.3 two-line output control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.4 system considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.5 programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.6 presto ii programming algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2.7 program inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.8 program verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.9 electronic signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.10 erasure operation (applies to uv eprom) . . . . . . . . . . . . . . . . . . . . . . . 11 3 maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 dc and ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.1 32-pin ceramic frit-seal dip, with round window (fdip32wa) . . . . . . . . 18 5.2 32-pin plastic dip, 600 mils width (pdip32) . . . . . . . . . . . . . . . . . . . . . . . 19 5.3 32-lead rectangular plastic leaded chip carrier (plcc32) . . . . . . . . . . 20 5.4 32-lead plastic thin small outline, 8x20 mm (tsop32) . . . . . . . . . . . . . 21 6 part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7 revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
m27c1001 list of tables 3/24 list of tables table 1. signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 table 2. operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 table 3. electronic signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 table 4. absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 table 5. read mode dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 6. programming mode dc characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 table 7. capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 table 8. ac measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 table 9. read mode ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 table 10. read mode ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 table 11. programming mode ac characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 table 12. fdip32wa package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 table 13. pdip32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 9 table 14. plcc32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 table 15. tsop32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 table 16. ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 table 17. document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
list of figures m27c1001 4/24 list of figures figure 1. logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 figure 2. dip connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 figure 3. lcc connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 4. tsop connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 figure 5. programming flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 figure 6. ac testing input output waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 4 figure 7. ac testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 figure 8. read mode ac waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 figure 9. programming and verify modes ac waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 figure 10. fdip32wa package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 figure 11. pdip32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 figure 12. plcc32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 figure 13. tsop32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
m27c1001 summary description 5/24 1 summary description the m27c1001 is a 1 mbit eprom offered in the two ranges: uv (ultra violet erase) and otp (one time programmable). it is ideally suited for microproce ssor systems requiring large programs and is organized as 131,072 words of 8 bits. the fdip32w (window ceramic frit-seal package) has a transparent lid that enables the user to expose the chip to ultraviolet light to erase the bit pattern. a new pattern can then be written to the device by following the programming procedure. for applications where the content is programmed only one time and erasure is not required, the m27c1001 is offered in pdip32, plcc32 and tsop32 (8 x 20 mm) packages. in order to meet environmental requirements, st offers the m27c1001 in ecopack? packages. ecopack packages are lead-free. the category of second level interconnect is marked on the package and on the inner box label, in compliance with jedec standard jesd97. the maximum ratings related to soldering conditions are also marked on the inner box label. ecopack is an st trademark. ecopack? specifications are available at: www.st.com. see figure 1: logic diagram and table 1: signal descriptions for a brief overview of the signals connected to this device. figure 1. logic diagram ai00710b 17 a0-a16 p q0-q7 v pp v cc m27c1001 g e v ss 8
summary description m27c1001 6/24 figure 2. dip connections table 1. signal descriptions signal description a0-a16 address inputs q0-q7 data outputs e chip enable g output enable p program v pp program supply v cc supply voltage v ss ground nc not connected internally a1 a0 q0 a7 a4 a3 a2 a6 a5 a13 a10 a8 a9 q7 a14 a11 g e q5 q1 q2 q3 v ss q4 q6 nc p a16 a12 v pp v cc a15 ai00711 m27c1001 8 1 2 3 4 5 6 7 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17
m27c1001 summary description 7/24 figure 3. lcc connections figure 4. tsop connections ai00712 nc a8 a10 q5 17 a1 a0 q0 q1 q2 q3 q4 a7 a4 a3 a2 a6 a5 9 p a9 1 a16 a11 a13 a12 q7 32 v pp v cc m27c1001 a15 a14 q6 g e 25 v ss a1 a0 q0 a7 a4 a3 a2 a6 a5 a13 a10 a8 a9 q7 a14 a11 g e q5 q1 q2 q3 q4 q6 nc p a16 a12 v pp v cc a15 ai01151b m27c1001 (normal) 8 1 9 16 17 24 25 32 v ss
device description m27c1001 8/24 2 device description ta bl e 2 lists the operating modes of the m27c1001. a single power supply is required in read mode. all inputs are ttl levels except for v pp and 12v on a9 for electronic signature. note: x = v ih or v il , v id = 12v 0.5v. 2.1 read mode the m27c1001 has two control functions, both of which must be logically active in order to obtain data at the outputs. chip enable (e ) is the power control and should be used for device selection. output enable (g ) is the output control and should be used to gate data to the output pins, independent of device selection. assuming that the addresses are stable, the address access time (t avqv ) is equal to the delay from e to output (t elqv ). data is available at the output after a delay of t glqv from the falling edge of g , assuming that e has been low and the addresses have been stable for at least t avqv -t glqv . 2.2 standby mode the m27c1001 has a standby mode which reduces the supply current from 30ma to 100a. the m27c1001 is placed in the standby mode by applying a cmos high signal to the e input. when in the standby mode, the outputs are in a high impedance state, independent of the g input. 2.3 two-line output control because eproms are usually used in larger me mory arrays, this product features a 2-line control function which accommodates the use of multiple memory connection. the two line control function allows: the lowest possible memory power dissipation, complete assurance that output bus contention will not occur. for the most efficient use of these two control lines, e should be decoded and used as the primary device selecting function, while g should be made a common connection to all devices in the array and connected to the read line from the system control bus. this table 2. operating modes mode e g p a9 v pp q7-q0 read v il v il xxv cc or v ss data out output disable v il v ih xxv cc or v ss hi-z program v il v ih v il pulse x v pp data in verify v il v il v ih xv pp data out program inhibit v ih xxxv pp hi-z standby v ih xxxv cc or v ss hi-z electronic signature v il v il v ih v id v cc codes
m27c1001 device description 9/24 ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is required from a particular memory device. 2.4 system considerations the power switching characteristics of advanced cmos eproms require careful decoupling of the devices. the supply current, i cc , has three segments that are of interest to the system designer: the standby current level, the active current level, and transient current peaks that are produced by the falling and rising edges of e . the magnitude of the transient current peaks is dependent on the capacitive and inductive loading of the device at the output. the associated transient voltage peaks can be suppressed by complying with the two line output control and by properly selected decoupling capacitors. it is recommended that a 0.1f ceramic capacitor be used on every device between v cc and v ss . this should be a high frequency capacitor of low inherent inductance and should be placed as close to the device as possible. in addition, a 4.7f bulk electrolytic capacitor should be used between v cc and v ss for every eight devices. the bulk capacitor should be located near the power supply connection point. the purpose of th e bulk capacitor is to overcome the voltage drop caused by the inductive effects of pcb traces. 2.5 programming when delivered (and after each erasure for uv eprom), all bits of the m27c1001 are in the '1' state. data is introduced by selectively programming '0's into the desired bit locations. although only '0's will be programmed, both '1 's and '0's can be present in the data word. the only way to change a '0' to a '1' is by die exposition to ultraviolet light (uv eprom). the m27c1001 is in the programming mode when v pp input is at 12.75v, e is at v il and p is pulsed to v il . the data to be programmed is applied to 8 bits in parallel to the data output pins. the levels required for the address and data inputs are ttl. v cc is specified to be 6.25v 0.25v. 2.6 presto ii programming algorithm presto ii programming algorithm allows the whole array to be programmed, with a guaranteed margin, in a typical time of 13 seconds. programming with presto ii involves in applying a sequence of 100s program pulses to each byte until a correct verify occurs (see figure 5 ). during programming and verify operation, a margin mode circuit is automatically activated in order to guarantee that each cell is programmed with enough margin. no overprogram pulse is applied since the verify in margin mode provides necessary margin to each programmed cell.
device description m27c1001 10/24 figure 5. programming flowchart 2.7 program inhibit programming of multiple m27c1001s in para llel with different data is also easily accomplished. except for e , all like inputs including g of the parallel m27c1001 may be common. a ttl low level pulse applied to a m27c1001's p input, with e low and v pp at 12.75v, will program that m2 7c1001. a high level e input inhibits the other m27c1001s from being programmed. 2.8 program verify a verify (read) should be performed on the programmed bits to determine that they were correctly programmed. the verify is accomplished with e and g at v il , p at v ih , v pp at 12.75v and v cc at 6.25v. 2.9 electronic signature the electronic signature (es) mode enables the reading out of a binary code from an eprom that will identify its manufacturer an d type. this mode is intended for use by programming equipment to automatically match the device to be programmed with its corresponding programming algorithm. the es mode is functional in the 25c 5c ambient temperature range that is required when programming the m27c1001. to activate the es mode, the programming equipment must force 11.5v to 12.5v on address line a9 of the m27c1001, with v pp = v cc = 5v. two identifier bytes may then be sequenced from the device outputs by toggling address line a0 from v il to v ih . all other address lines must be held at v il during electronic signature mode. ai00715c n = 0 last addr verify p = 100 s pulse ++n = 25 ++ addr v cc = 6.25v, v pp = 12.75v fail check all bytes 1st: v cc = 6v 2nd: v cc = 4.2v yes no yes no yes no
m27c1001 device description 11/24 byte 0 (a0 = v il ) represents the manufacturer code and byte 1 (a0 = v ih ) the device identifier code. for the stmicroelectronics m27c1001, these two identifier bytes are given in ta b l e 3 and can be read-out on outputs q7 to q0. 2.10 erasure operation (applies to uv eprom) the erasure characteristics of the m27c1001 is such that erasure begins when the cells are exposed to light with wavelengths shorter than approximately 4000 ?. it should be noted that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000 ? range. research shows that constant exposure to room level fluorescent lighting could erase a typical m27c1001 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunligh t. if the m27c1001 is to be exposed to these types of lighting conditions for extended periods of time, it is suggested that opaque labels be put over the m27c1001 window to prevent unintentional erasure. the recommended erasure procedure for the m27c1001 is exposure to short wave ultraviolet light which has a wavelength of 2537 ?. the integrated dose (i.e. uv intensity x exposure time) for erasure should be a minimum of 15 w-sec/cm 2 . the erasure time with this dosage is approximately 15 to 20 minutes using an ultraviolet lamp with 12000 w/cm 2 power rating. the m27c1001 should be placed within 2.5 cm (1 inch) of the lamp tubes during the erasure. some lamps have a filter on their tubes which should be removed before erasure. table 3. electronic signature identifier a0 q7 q6 q5 q4 q3 q2 q1 q0 hex data manufacturer?s code v il 00100000 20h device code v ih 00000101 05h
maximum ratings m27c1001 12/24 3 maximum ratings table 4. absolute maximum ratings (1) 1. except for the rating "operating temperature range" , stresses above those listed in the table "absolute maximum ratings" may cause permanent damage to the device. these are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied. exposure to absolute maximum ra ting conditions for extended periods may affect device reliability. refer also to the st microelectronics sure program and other relevant quality documents. symbol parameter value unit t a ambient operating temperature (2) 2. depends on range. ?40 to 125 c t bias temperature under bias ?50 to 125 c t stg storage temperature ?65 to 150 c v io (3) 3. minimum dc voltage on input or output is ?0.5v wi th possible undershoot to ?2.0v for a period less than 20ns. maximum dc voltage on output is vcc +0.5v with pos sible overshoot to vcc +2v for a period less than 20ns. input or output voltage (except a9) ?2 to 7 v v cc supply voltage ?2 to 7 v v a9 (3) a9 voltage ?2 to 13.5 v v pp program supply voltage ?2 to 14 v
m27c1001 dc and ac characteristics 13/24 4 dc and ac characteristics t a = 0 to 70c, ?40 to 85c or ?40 to 125c; v cc = 5v 5% or 5v 10%; v pp = v cc t a = 25 c; v cc = 6.25v 0.25v; v pp = 12.75v 0.25v table 5. read mode dc characteristics (1) 1. v cc must be applied simultaneously with or before v pp and removed simultaneously or after v pp . symbol parameter test condition min. max. unit i li input leakage current 0v v in v cc 10 a i lo output leakage current 0v v out v cc 10 a i cc supply current e = v il , g = v il , i out = 0ma, f = 5mhz 30 ma i cc1 supply current (standby) ttl e = v ih 1ma i cc2 supply current (standby) cmos e > v cc ? 0.2v 100 a i pp program current v pp = v cc 10 a v il input low voltage ?0.3 0.8 v v ih (2) 2. maximum dc voltage on output is v cc +0.5v. input high voltage 2 v cc + 1 v v ol output low voltage i ol = 2.1ma 0.4 v v oh output high voltage ttl i oh = ?400a 2.4 v output high voltage cmos i oh = ?100a v cc ? 0.7v v table 6. programming mode dc characteristics (1) 1. v cc must be applied simultaneously with or before v pp and removed simultaneously or after v pp . symbol parameter test condition min. max. unit i li input leakage current v il v in v ih 10 a i cc supply current 50 ma i pp program current e = v il 50 ma v il input low voltage ?0.3 0.8 v v ih input high voltage 2 v cc + 0.5 v v ol output low voltage i ol = 2.1ma 0.4 v v oh output high voltage ttl i oh = ?400a 2.4 v v id a9 voltage 11.5 12.5 v
dc and ac characteristics m27c1001 14/24 t a = 25 c, f = 1 mhz figure 6. ac testing input output waveform figure 7. ac testing load circuit table 7. capacitance (1) 1. sampled only, not 100% tested. symbol parameter test condition min max unit c in input capacitance v in = 0v 6 pf c out output capacitance v out = 0v 12 pf table 8. ac measurement conditions parameter high speed standard input rise and fall times 10ns 20ns input pulse voltages 0 to 3v 0.4v to 2.4v input and output timing ref. voltages 1.5v 0.8v and 2v ai01822 3v high speed 0v 1.5v 2.4v standard 0.4v 2.0v 0.8v ai01823b 1.3v out c l c l = 30pf for high speed c l = 100pf for standard c l includes jig capacitance 3.3k ? 1n914 device under test
m27c1001 dc and ac characteristics 15/24 t a = 0 to 70c, ?40 to 85c or ?40 to 125c; v cc = 5v 5% or 5v 10%; v pp = v cc table 9. read mode ac characteristics (1) 1. v cc must be applied simultaneously with or before v pp and removed simultaneously or after v pp . symbol alt parameter test condition m27c1001 unit -35 (2) 2. speed obtained with high speed ac measurement conditions. -45 -60 -70 min. max. min. max. min. max. min. max. t avqv t acc address valid to output valid e = v il , g = v il 35 45 60 70 ns t elqv t ce chip enable low to output valid g = v il 35 45 60 70 ns t glqv t oe output enable low to output valid e = v il 25 25 30 35 ns t ehqz (3) 3. sampled only, not 100% tested. t df chip enable high to output hi-z g = v il 025025030030ns t ghqz (3) t df output enable high to output hi- z e = v il 025025030030ns t axqx t oh address transition to output tr a n s i t i o n e = v il , g = v il 0000ns
dc and ac characteristics m27c1001 16/24 t a = 0 to 70c, ?40 to 85c or ?40 to 125c; v cc = 5v 5% or 5v 10%; v pp = v cc figure 8. read mode ac waveforms table 10. read mode ac characteristics (1) 1. v cc must be applied simultaneously with or before v pp and removed simultaneously or after v pp . symbol alt parameter test condition m27c1001 unit -80 -90 -10 -12/-15/ -20/-25 min max min max min max min max t avqv t acc address valid to output valid e = v il , g = v il 80 90 100 120 ns t elqv t ce chip enable low to output valid g = v il 80 90 100 120 ns t glqv t oe output enable low to output valid e = v il 40 45 50 60 ns t ehqz (2) 2. sampled only, not 100% tested. t df chip enable high to output hi-z g = v il 030030030040ns t ghqz (2) t df output enable high to output hi-z e = v il 030030030040ns t axqx t oh address transition to output transition e = v il , g = v il 0000ns ai00713b taxqx tehqz a0-a16 e g q0-q7 tavqv tghqz tglqv telqv valid hi-z valid
m27c1001 dc and ac characteristics 17/24 t a = 25 c; v cc = 6.25v 0.25v; v pp = 12.75v 0.25v figure 9. programming and verify modes ac waveforms table 11. programming mode ac characteristics (1) 1. v cc must be applied simultaneously with or before v pp and removed simultaneously or after v pp . symbol alt parameter test condition min. max. unit t avpl t as address valid to program low 2 s t qvpl t ds input valid to program low 2 s t vphpl t vps v pp high to program low 2 s t vchpl t vcs v cc high to program low 2 s t elpl t ces chip enable low to program low 2 s t plph t pw program pulse width 95 105 s t phqx t dh program high to input transition 2 s t qxgl t oes input transition to output enable low 2 s t glqv t oe output enable low to output valid 100 ns t ghqz (2) 2. sampled only, not 100% tested. t dfp output enable high to output hi-z 0 130 ns t ghax t ah output enable high to address transition 0ns tavpl valid ai00714 a0-a16 q0-q7 v pp v cc p g data in data out e tqvpl tvphpl tvchpl tphqx tplph tglqv tqxgl telpl tghqz tghax program verify
package mechanical data m27c1001 18/24 5 package mechanical data 5.1 32-pin ceramic frit-seal dip, with round window (fdip32wa) figure 10. fdip32wa package outline table 12. fdip32wa package mechanical data symbol millimeters inches min typ max min typ max a5.720.225 a1 0.51 1.40 0.020 0.055 a2 3.91 4.57 0.154 0.180 a3 3.89 4.50 0.153 0.177 b 0.41 0.56 0.016 0.022 b1 1.45 0.057 c 0.23 0.30 0.009 0.012 d 41.73 42.04 1.643 1.655 d2 38.10 1.500 e 2.54 0.100 e 15.24 0.600 e1 13.06 13.36 0.514 0.526 ea 14.99 0.590 eb 16.18 18.03 0.637 0.710 l 3.18 4.10 0.125 0.161 n32 32 s 1.52 2.49 0.060 0.098 ? 7.11 0.280 4 11 4 11 fdipw-a a3 a1 a l b1 b e d s e1 e n 1 c ea d2 ? eb a2
m27c1001 package mechanical data 19/24 5.2 32-pin plastic dip, 600 mils width (pdip32) figure 11. pdip32 package outline table 13. pdip32 package mechanical data symbol millimeters inches min typ max min typ max a4.830.190 a1 0.38 0.015 a2 3.81 0.150 b 0.41 0.53 0.016 0.021 b1 1.14 1.65 0.045 0.065 c 0.23 0.38 0.009 0.015 d 41.78 42.29 1.645 1.665 d2 38.10 1.500 ea 15.24 0.600 e 2.54 0.100 e 15.24 15.88 0.600 0.625 e1 13.46 13.97 0.530 0.550 s 1.65 2.21 0.065 0.087 l 3.05 3.56 0.120 0.140 0 15 0 15 n32 32 pdip-c a2 a1 a l b1 b e d s e1 e n 1 c ea d2
package mechanical data m27c1001 20/24 5.3 32-lead rectangular plastic leaded chip carrier (plcc32) figure 12. plcc32 package outline table 14. plcc32 package mechanical data symbol millimeters inches min typ max min typ max a 3.18 3.56 0.125 0.140 a1 1.53 2.41 0.060 0.095 a2 0.38 0.015 b 0.33 0.53 0.013 0.021 b1 0.66 0.81 0.026 0.032 cp 0.10 0.004 d 12.32 12.57 0.485 0.495 d1 11.35 11.51 0.447 0.453 d2 4.78 5.66 0.188 0.223 d3 7.62 0.300 e 14.86 15.11 0.585 0.595 e1 13.89 14.05 0.547 0.553 e2 6.05 6.93 0.238 0.273 e3 10.16 0.400 e 1.27 0.050 f 0.00 0.13 0.000 0.005 r 0.89 0.035 n32 32 plcc-a d e3 e1 e 1 n d1 d3 cp b e2 e b1 a1 a r 0.51 (.020) 1.14 (.045) f a2 e2 d2 d2
m27c1001 package mechanical data 21/24 5.4 32-lead plastic thin small outline, 8x20 mm (tsop32) figure 13. tsop32 package outline table 15. tsop32 package mechanical data symbol millimeters inches min typ max min typ max a 1.200 0.0472 a1 0.050 0.150 0.0020 0.0059 a2 0.950 1.050 0.0374 0.0413 b 0.170 0.250 0.0067 0.0098 c 0.100 0.210 0.0039 0.0083 cp 0.100 0.0039 d 19.800 20.200 0.7795 0.7953 d1 18.300 18.500 0.7205 0.7283 e 0.500 0.0197 e 7.900 8.100 0.3110 0.3189 l 0.500 0.700 0.0197 0.0276 n32 32 0 5 0 5 tsop-a d1 e 1 n cp b e a2 a n/2 d die c l a1
part numbering m27c1001 22/24 6 part numbering table 16. ordering information scheme for a list of available options (speed, package, etc...) or for further information on any aspect of this device, please contact the stmi croelectronics sales of fice nearest to you. example: m27c1001 -35 x c 1 tr device type m27 supply voltage c = 5v device function 1001 = 1 mbit (128kb x 8) speed -35 (1) = 35 ns -10 = 100 ns 1. high speed, see ac characteristi cs section for further information. -45 = 45 ns -12 = 120 ns -60 = 60 ns -15 = 150 ns -70 = 70 ns -20 = 200 ns -80 = 80 ns -25 = 250 ns -90 = 90 ns v cc tolerance blank = 10% x = 5% package f = fdip32w c = plcc32 b = pdip32 n = tsop32: 8 x 20 mm temperature range 1 = 0 to 70 c 3 = ?40 to 125 c 6 = ?40 to 85 c options tr = ecopack? package, tape & reel packing
m27c1001 revision history 23/24 7 revision history table 17. document revision history date revision changes september 1998 1 first issue 24-jan-2000 2 35ns speed class addes (table 8a, ta bl e 1 6 ) 20-sep-2000 3 an620 reference removed 04-jun-2002 4 plcc32 package mechanical data and drawing clarified ( ta b l e 1 4 and figure 12 ) tsop32 package mechanical data clarified ( ta b l e 1 5 ) 12-apr-2006 5 removed lcc32w package and additional burn-in option. converted to new template. added ecopack? information.
m27c1001 24/24 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. unless expressly approved in writing by an authorize representative of st, st products are not designed, authorized or warranted for use in military, air craft, space, life saving, or life sustaining applications, nor in products or systems, where failure or malfunction may result in personal injury, death, or severe property or environmental damage. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2006 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com

▲Up To Search▲

Price & Availability of M27C1001-15B1

	To Download M27C1001-15B1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .